How to Light a Gas Fireplace

Posted on

How to Light a Gas Fireplace –  Gas Fireplaces provide warmth and a warm Atmosphere in almost every Home. They burn cleaner than a conventional Wood-burning Fireplace and do not Produce Ash or Soot for Cleaning. Although many Gas Fireplaces have a Button or Ignition Switch to illuminate the Fire, some old Gas Fireplaces have put a Metal key Into a Keyhole that activates the flow of Gas To light the Fire.

How to Light A Gas Fireplace Lovely Gas Fireplace Panies New 19 My Gas Fireplace Will Not Light B3u
Gas Fireplace panies New 19 My Gas Fireplace Will Not Light B3u

Most Gas Fireplaces have a permanent Night light, which is a small Flame that burns even if You don’t use the Fireplace. That makes the Fireplace easy to start when it’s cold outside, but when it warms up, it’s a good Idea to turn off the Pilot to save Gas.

If you do, you have to restart it at the Start of the next cold Season. The Procedure is not exactly the same for all Models; Older People don’t have an electronic Spark. Although the Procedure is slightly different, most Of the steps are the same.

How to Light A Gas Fireplace Luxury How to Light Gas Fireplace Pilot without Ignitor
How to Light Gas Fireplace Pilot without Ignitor

Remove the decorative Lid from the Fireplace to show the gas Controls at the Bottom of the Unit near the Floor. You should see a Gas Cordon Valve. Turn the Handle parallel to the Direction of the Gas Lines to turn on the gas. If you don’t see the Valve, it’s probably behind the Chimney. Find him there and turn him on. Remove The solid Glass from the Fireplace. This is an important Safety Measure that prevents the Accumulation of Gas when the Pilot has been difficult to ignite.

Find The Gas Control Button. Just above, you should see a red or black Push button, which means the Device has a piezoelectric Spark Mechanism. Press the Button once or twice to check if there is a Spark at the End of the Pilot tube. If You don’t see a Button, You need to turn on the Flame manually.

How to Light A Gas Fireplace Inspirational Creative Gas Fireplace Wont Light Amazing Home Design Unique
Creative Gas Fireplace Wont Light Amazing Home Design Unique

Rotate the Throttle until the “driver ” setting is aligned with the sharp Marker on the outer Edge of the Control. Press the Button while Pressing the Starter. If the Driver doesn’t turn on, wait 10 Seconds and press again. Keep it until the Driver starts.

Now comes the Part that makes the Gas Fireplace so comfortable, the Lighting of the Blaze, which will hopefully stay as long as necessary. Light the Flame With a Long-range game or lighter if there is no piezoelectric Control. Hold the Gas Control Button while Holding the End of an illuminated match or the Lighter At the End of the Pilot’s Tube. The Pilot must start as soon as the Blaze is close enough.

How to Light A Gas Fireplace Beautiful Napoleon Direct Vent Gas Fireplace Insert with Night Light In
Napoleon Direct Vent Gas Fireplace Insert with Night Light in

Hold the Control Button for about 20 Seconds to give the thermopaar time for Heating, then detach it. The Pilot is expected to stay. If not, turn it back on and Hold the Button a little longer. Turn the Button into the “on ” position, then replace the solid Glass and The Ornamental lid.

If the Fireplace is new or the Pilot has not been lit for a long time, there can be Air in the Pilot Clock. This makes it difficult to turn on, but should light up after repeated attempts. If You find that You need to illuminate the Pilot frequently, the Pilot’s Watch can be hampered by Debris. Therefore, Be Sure to clean the End of the Tube with a PIN.

How to Light A Gas Fireplace Best Of Gas Fireplace Contemporary Closed Hearth 3 Sided Matrix 1050
Gas fireplace contemporary closed hearth 3 sided MATRIX 1050

If the Pilot is particularly hard to start and You start smelling Gas, Stop and wait for the Gas to disperse before Trying again. It can be dangerous to light it up if there’s a strong Smell of Gas, so Try to air the Area a little bit before Trying to turn the Pilot back on.